Setting orientation and tilt correctly takes a few minutes with a compass and an inclinometer. This guide explains which way to face the array, how steep to set it for your latitude and season, how much a small error really costs, and which site conditions should change the setting.
Face the equator
The basic rule is simple: in the southern hemisphere the panels should face true north, and in the northern hemisphere they should face true south. Facing the equator lets the array collect the most sunlight across the day and the year.
True direction is not the same as magnetic direction. A compass points to magnetic north, which differs from true north by the local magnetic declination. In some regions that difference is small; in others it can be well over ten degrees. Look up the declination for the site before setting up, or use a phone or GPS tool that shows true bearing.
Tilt by latitude
For year-round energy, a tilt roughly equal to the site latitude is a reasonable starting point. A site at 26 degrees south would use a tilt of about 26 degrees from horizontal. Many trailer frames offer a set of fixed tilt positions, so choose the one closest to the target.
Yield modelling for a specific site often shows the annual optimum slightly below latitude, because summer days are longer and diffuse light favours flatter panels. For a trailer that may move between sites, latitude is a practical, easily remembered rule.
Bias for the hardest season
Off-grid trailers are usually sized for the season with the least sunlight, because that is when the battery is most likely to run short. If the load is steady all year, tilting steeper than latitude, often by 10 to 15 degrees, raises winter output at the cost of some summer energy that the battery could not store anyway.
Where loads peak in summer, such as cooling or water pumping, a flatter tilt favours the high sun. Match the tilt to the season in which the trailer is closest to its limit. Our guide to daily output estimates shows how to check whether the array is the limiting factor in the first place.
Minimum tilt near the equator
Close to the equator the latitude rule suggests an almost flat array. In practice panels should keep a minimum tilt of about 10 degrees so that rain washes dust off and water does not pool along the frame edge. Flat panels on a dusty site soil quickly and lose more energy to dirt than they gain from geometry.
Within a few degrees of the equator the sun passes to the north for part of the year and to the south for the rest, so a low tilt facing either way performs similarly over a full year.
What an orientation error really costs
Small errors cost less than many people expect. Because the sun sweeps across the sky from east to west, a modest error in direction mainly shifts output a little earlier or later in the day rather than cutting it heavily, and diffuse light softens the effect further. A 10 degree error loses well under 1 percent, and a 20 degree error typically around 2 to 3 percent of annual energy.
Large errors are another matter. An array facing east or west at a moderate tilt can lose 10 to 20 percent, and one facing away from the equator far more. So the priority on arrival is to avoid gross errors; fine-tuning to the exact degree matters much less.
East-west splits for daytime loads
Some trailers carry two panel wings that can be set facing east and west. This spreads output across the day, producing more in the morning and late afternoon and less at midday. Total daily energy is usually somewhat lower than an equator-facing array, but the flatter profile suits loads that run steadily through daylight, such as site offices, pumps or charging stations.
It can also ease battery stress on sites where midday surplus would otherwise be clipped once the battery is full.
Shading checks on site
A shaded corner can drag down the output of a whole string. Before setting up, look along the sun’s path for the season: containers, site buildings, stockpiles, masts and trees that are harmless at midday can cast long shadows in the morning and afternoon, especially in winter when the sun is low.
As a rule of thumb, keep obstacles at a distance of at least two to three times their height on the equator side of the trailer. Our article on ballast, wind and ground conditions covers the other site checks to make before the frame is raised.
Wind, stow and soiling
Steeper tilt means more wind load. Every trailer has a maximum wind speed for each tilt setting and a stow position for storms. On exposed sites it can make sense to use a lower tilt than the energy optimum, accepting a small yield loss for more margin and fewer manual stow events.
Dust deposits faster on flatter panels. On mine and quarry sites, a slightly steeper tilt and a regular cleaning routine protect output more than precise orientation.
Setting up and recording
On arrival, level the trailer, confirm true direction with a corrected compass or GPS bearing, set the tilt with an inclinometer on the panel frame and check for shading at the low-sun hours. Record the bearing, tilt, date and site latitude in the trailer log, and photograph the setting.
If the trailer stays for more than a season, plan a tilt adjustment at the change of season. Where trailers support larger remote power systems, our hybrid power systems team can integrate them with generators and fixed storage.
About the authors
This guide comes from the USP&E hybrid power engineers and field technicians who deploy solar trailers and remote power systems on mine, construction and telecom sites. USP&E is an EPC and O&M contractor, not a broker, with 150+ power projects in 45+ countries, 25,000 MW contracted since 2002 and 24+ years in the field. Larger remote installations are delivered through our power plant EPC work.
Offices: Colorado Springs (1755 Telstar Dr, Suite 300), Knoxville (800 S Gay St, Suite 700), London (162-168 Regent Street), Johannesburg (22 Kildoon Rd, Bryanston), Cape Town (31 Brickfield Road, Woodstock) and China (No. 1 Ningzhou Road, Wuxi). Regions: USA | AFRICA | UK | UAE | CHINA. ISO 9001 and ISO 45001 certified.
Tilt and orientation questions
Which way should solar trailer panels face?
Toward the equator: true north in the southern hemisphere and true south in the northern hemisphere. Correct the compass for magnetic declination.
What tilt angle should a solar trailer use?
A tilt close to the site latitude works well year round. Add about 10 to 15 degrees to favour winter output on steady off-grid loads.
What is the minimum tilt for solar panels?
About 10 degrees, so that rain can wash off dust and water does not pool, even close to the equator.
How much energy is lost if the trailer faces the wrong way?
A 10 to 20 degree error usually costs only a few percent, but facing east, west or away from the equator can cost far more.
Should panels be flatter on windy sites?
Often yes. A lower tilt reduces wind load and stow events, at the cost of a small loss in energy.
How do I set the tilt on site?
Level the trailer, then place an inclinometer on the panel frame and adjust to the chosen angle before locking the frame.
Plan your trailer deployment
Tell us your site location, loads and season of use, and our engineers will suggest orientation, tilt and battery settings for your solar trailers.
Use the mobile power enquiry form for a structured request, email info@uspeglobal.com with any site data you hold, or ring +27 10 822 2324 to speak to an engineer. Assist generators for solar trailer sites are listed among our diesel generator sets.