This guide explains how MPPT and PWM controllers differ, how to size a controller for the array and battery on a trailer, which charging settings matter for each battery chemistry and how the controller works alongside an inverter and a backup generator on remote sites.
What the charge controller does
Solar panels produce a voltage and current that change with sunlight and temperature. The battery needs a controlled charge: enough current to fill it during the day, a limit on voltage to avoid overcharging and a way to stop discharge before damage. The charge controller manages all of this and, on many units, also reports data to the trailer’s monitoring system.
On a trailer the controller works in harder conditions than on a rooftop: vibration during transport, dust, heat inside the enclosure and a battery that may be cycled deeply every night. These conditions shape the choice as much as the electrical figures.
PWM and MPPT compared
A PWM controller connects the array almost directly to the battery and switches it on and off to regulate charge. The panels are forced to operate at battery voltage, which is usually well below their best operating point, so some of their power is lost. PWM units are simple and cheap and suit very small systems where panel and battery voltages are closely matched.
An MPPT controller, maximum power point tracking, contains a DC to DC converter. It runs the array at the voltage where it produces the most power and converts that to the voltage the battery needs. Gains of 15 to 30 percent over PWM are common, and more in cold weather, which is why MPPT is standard on commercial solar power trailers.
Why array voltage matters
With MPPT, the array can be wired in series strings at a much higher voltage than the battery. A higher string voltage carries the same power with less current, so smaller cables and lower losses between the folding panel frame and the controller, which matters when panels are spread across telescopic or tilting frames.
The limit is the controller’s maximum input voltage. Panel voltage rises as temperature falls, so the coldest morning sets the design point. Exceeding the input limit, even briefly, can destroy the controller.
Sizing the controller: a worked example
Take a trailer with ten 450 watt panels and a 48 volt battery bank. Each panel has an open-circuit voltage of about 49 volts at standard test conditions and a temperature coefficient of minus 0.28 percent per degree. On a 0 degree morning the voltage rises by about 7 percent, to roughly 52.4 volts per panel.
Wired as two strings of five, the cold open-circuit voltage is about 262 volts, so the controller needs an input rating comfortably above that, such as 300 volts or more. The output current is roughly array power divided by battery charging voltage: 4,500 watts over about 54 volts gives 83 amps, so a 100 amp controller, or two 50 amp units, leaves sensible margin. The daily energy calculation for a trailer shows how to check that this array can meet the site load.
Charging stages and battery chemistry
Most controllers charge in stages: bulk, where maximum current flows; absorption, where voltage is held while the battery tops up; and float, a lower voltage that maintains a full battery. Lithium iron phosphate batteries usually need a short absorption and no float or a low float, while lead-acid types need longer absorption and periodic equalisation if the maker allows it.
Setting the controller to the wrong profile is a frequent cause of early battery failure. Our article on battery storage for solar trailers covers how chemistry choice affects cycle life, and the charge settings must follow the battery maker’s data sheet rather than the controller’s default.
Temperature compensation and battery management
Lead-acid batteries need their charge voltage lowered in heat and raised in cold. A battery temperature sensor connected to the controller handles this automatically. Without it, a trailer parked in desert sun may overcharge every afternoon.
Lithium batteries rely on their own battery management system. The controller should communicate with it, so the battery can reduce or stop charging when cell temperatures are too high or too low. Charging lithium cells below freezing can damage them permanently.
Load outputs and low-voltage disconnect
Some controllers include a load output with a low-voltage disconnect that switches off connected equipment before the battery is drained too far. On larger trailers the inverter normally performs this role, but small trailers feeding cameras, lights or radios often use the controller output directly.
Disconnect and reconnect thresholds should be chosen so that critical loads such as security cameras keep running as long as possible while the battery still keeps a reserve for the next morning.
Working with an inverter and backup generator
On hybrid trailers, the controller charges the battery from the sun, the inverter supplies AC loads and a small generator starts when the battery runs low. The controller and inverter must agree on battery voltage targets, or they will fight each other and cycle the generator unnecessarily.
Systems from one maker with a shared communication bus avoid most of these problems. Where mixed brands are used, settings should be tested over several days before the trailer goes to a remote site.
Heat, dust and fault finding
Controllers lose capacity as they get hot, and many reduce output above 40 to 45 degrees inside the enclosure. Shaded mounting, filtered ventilation and leaving space around heat sinks keep them working at full rating. Dust filters need cleaning on the same schedule as the panels.
When harvest falls, check panel cleanliness, string connections and controller input voltage before blaming the battery. Logged data from remote telemetry on the trailer usually shows quickly whether the controller, the array or the battery is the cause. Fleets of trailers benefit from a planned maintenance and service routine so that controller settings and firmware stay consistent across units.
About the authors
This guide comes from the USP&E electrical engineers and field technicians who size charge controllers and battery banks for the off-grid solar trailers and hybrid units we put on remote jobs. USP&E is an EPC and O&M contractor, not a broker, with 150+ power projects in 45+ countries, 25,000 MW contracted since 2002 and 24+ years in the field. Our solar, battery and generator hybrid systems apply the same controller principles at larger scale.
Offices: Colorado Springs (1755 Telstar Dr, Suite 300), Knoxville (800 S Gay St, Suite 700), London (162-168 Regent Street), Johannesburg (22 Kildoon Rd, Bryanston), Cape Town (31 Brickfield Road, Woodstock) and China (No. 1 Ningzhou Road, Wuxi). Regions: USA | AFRICA | UK | UAE | CHINA. ISO 9001 and ISO 45001 certified.
Charge controller questions
Is MPPT better than PWM for a solar trailer?
Yes for most commercial trailers. MPPT typically harvests 15 to 30 percent more energy and lets the array run at higher voltage.
How do I size an MPPT charge controller?
Compare each string’s open-circuit voltage on the coldest expected morning with the input limit, then divide array power by battery charge voltage for current, with margin.
Why does cold weather matter for controller sizing?
Panel voltage rises as temperature falls, and exceeding the controller’s maximum input voltage can destroy it.
Do lithium batteries need different charge settings?
Yes. They usually need a short absorption stage and little or no float, and they must not be charged below freezing.
What is a low-voltage disconnect?
It is a function that switches off loads before the battery is discharged too far, protecting its life.
Why does a controller lose output in hot weather?
Most controllers reduce current to protect themselves when internal temperature rises, so shading and ventilation matter.
Size your trailer charging system
Send your site loads, location and preferred battery type, and our engineers will help size the array, charge controller and battery for a mobile solar power trailer.
Use the solar trailer enquiry form for a structured request, email info@uspeglobal.com with any site data you hold, or ring +27 10 822 2324 to speak to an engineer. Backup generating sets for hybrid trailer systems are listed in our diesel set inventory.